Because your bathrooms are exposed to various humidity, excessive traffic, and one-of-a-kind cleaning products, they have got to be included by using a material which can deal with these extreme factors. Installing porcelain tile is one in every of the best options you can make when designing a new bathroom.
Porcelain tiles are totally recommended for the bathroom and kitchen because they are not protected by way of enamel, and the finish is generally polished, of great toughness and water-resistant. Their very low water absorption discourages any type of bathroom fungi from blooming. Not to mention that porcelain is harder and extra resistant than normal ceramic.
Porcelain is not only splendid for bathrooms and kitchens, however it is additionally used outside or in high-traffic areas such as living rooms, hallways or even shopping centers. Porcelain tile lasts longer, is scratch-resistant, has fantastic resistance to temperatures, and is very tough and durable.
Tools needed for installing porcelain tile
- Tape for measurement
- Rubber mallet
- Ceramic cutter
- Angular grinder
- Bucket to mix concrete
- Notched trowel
- Diamond cutting disc
- Laser level
- Safety rubber gloves
- Safety glasses
Materials needed for installing porcelain tile:
- Adhesive EF for stone and porcelain, forty four pounds
- Floor leveler, 55-pound bag
- Porcelain tile slabs (quantity will range with length of surface to cover)
Directions for installing porcelain tile
1. Do the ordinary math
First, you need to calculate the vicinity to be tiled for the project. If you are installing porcelain tile on the wall, you wish to multiply the size of the wall by using the height of the room, remembering to subtract the locations (width x height) of any windows and doors. If you’re installing porcelain tile on the floor, then truely multiply the width of the vicinity to be tiled by using the length of the place to be tiled.
PRO TIP: It is necessarily recommended to reserve one more field of material for future contingencies. For an exceedingly big space, you may think about getting 10% more of any fabric used.
2. Preparing the floor of the floor
If you opt to level out the ground before installing porcelain tile, it is advisable to use a floor leveler with a greatest thickness of 0.8 inches. If you would like install the new tile on appropriate of existing tile, you have to make sure there is an acceptable adhesive layer, as defined below.
3. Preparing the surface of the walls
If your wall is concrete or plaster, you just have got to wash the floor with mild soap and water. It doesn’t subject if the floor remains wet— the specialists name this a “saturated surface” — because it’s going to avoid the blend from drying up.
In the case of partition walls, it’s endorsed to first disguise them with textured fiber cement, since the resulting hard floor will supply the adhesive and tile slabs a greater grip.
4. Preparing the adhesive
Powdered adhesives are pre-dosed, meaning they come with all the necessary additives to accomplish a perfect adhesive paste — all you ought to do is add the water.
Pour the adhesive powder into a bucket and add water little by way of little; stir with a spatula until you get a thick, even paste.
5. Installing slabs on the floor
The slabs for the ground always move on first, since tiles for the partitions need to remain on precise to permit water to run down with out problems.
Gluing the slabs is done with a notched trowel — its enamel depart the strips essential for the adhesive to have higher grip. The locations with out adhesive are left with air pockets which will cause suction once the slabs settle; this also facilitates the adhesive to dry better.
Once the porcelain has been put on accurate of the adhesive, the slabs have got to be tapped lightly with a rubber mallet.
Leave overlapping joints among each run of slabs.
6. Installing slabs on the walls
As in the directions above for installing porcelain tile on the floor, gluing slabs for the wall is completed with a notched trowel. Wall slabs also need to be tapped lightly with a rubber mallet.
Getting instantly cuts on slabs
Use a ceramic cutter that cuts, ratings and snaps wall and floor tiles. There’s a manage in the cutter that permits you to observe pressure on the tile and also allows to lead the cutter along the rails of the cutter. The tungsten-carbide wheel in the cutter is what correctly ratings the surface of the tile and lets you make the cut.
Getting curved cuts on slabs
To install porcelain on the floor and walls of a bathroom, some pieces will want curved or circular cuts to coincide with the drains and water outlets. These cuts are made with an angular grinder and a diamond cutting disc. The cut on the slab should be approximately 0.1-inch bigger than the diameter of the drain or water outlet.
Read more: What Is The Change Between Ceramic And Porcelain Tile?